Showing 23 results for Abbas
Alireza Zibanejad-Rad, Ali Alizadeh, Seyyed Mehdi Abbasi,
Volume 21, Issue 2 (June 2024)
Abstract
Pressureless sintering was employed at 1400 °C to synthesize Ti matrix composites (TMCs) reinforced with in-situ TiB and TiC reinforcements using TiB2 and B4C initial reinforcements. The microstructure and wear behavior of the synthesized composites were evaluated and compared and the results showed that B4C caused the formation of TiB-TiC in-situ hybrid reinforcements in the Ti matrix. Also, TiB was in the form of blades/needles and whiskers, and TiC was almost equiaxed. Moreover, the volume fraction of the in-situ formed reinforcement using B4C was much higher than that formed using TiB2. In addition, although the hardness of the B4C-synthesized composites was higher, the composite synthesized using 3 wt.% TiB2 exhibited the highest hardness (425 HV). The wear test results showed that the sample synthesized using 3 wt.% TiB2 showed the lowest wear rate at 50 N, mainly because of its higher hardness. The dominant wear mechanism in the samples synthesized using 3 wt.% B4C was abrasive and delamination at 50 N and 100 N, respectively while in the samples synthesized 3 wt.% TiB2, a combination of delamination and adhesive wear and adhesive wear was ruling, respectively.
Zeinab Abbasali Karajabad, Adrine Malek Khachatourian, Mohammad Golmohammad, Ali Nemati,
Volume 22, Issue 1 (March 2025)
Abstract
Hybrid asymmetric supercapacitors using distinct cathode/anode materials offer enhanced energy density by expanding operational potential windows compared to symmetric configurations. In this work rGO/α-Fe₂O₃ and rGO/TiO₂ nanocomposites were synthesized via hydrothermal method for hybrid asymmetric supercapacitors applications. Field emission scanning electron microscope (FESEM) revealed uniform distribution of spherical α-Fe₂O₃ and TiO₂ nanoparticles on rGO sheets. The X-ray diffractometry (XRD) analysis confirmed the presence of the hematite and anatase in the rGO/α-Fe2O3 and rGO/TiO2 nanocomposites, respectively. Additionally, in the XRD spectra of both nanocomposites, a broad peak corresponding to the (002) crystalline planes of rGO was observed. Electrochemical testing showed specific capacities of 130 F/g (rGO/α-Fe₂O₃) and 253 F/g (rGO/TiO₂) at 5 mV/s in 1M KOH. The assembled hybrid asymmetric supercapacitors (rGO/α-Fe₂O₃//rGO/TiO₂) achieved a 1.6 V operational potential window. Power density and energy density of 1066 W kg-1 and 9.7 Wh kg-1 were achieved at a current density of 1 A/g, respectively.
Mahdi Rajaee, Mahdi Raoufi, Zeinab Malekshahi Beiranvand, Abbas Naeimi,
Volume 22, Issue 2 (JUNE 2025)
Abstract
This research explored the impact of the nickel-to-manganese ratio and the influence of the matrix phase on the properties of W-Ni-Mn tungsten heavy alloys (WHAs), aiming to determine the optimal composition for achieving desirable alloy properties. For this purpose, tungsten, nickel, and manganese powders with specified weight percentages underwent two rounds of wet milling. Powder mixtures were obtained with weight ratios of 90W-6Ni-4Mn, 90W-8Ni-2Mn, and 88W-10Ni-2Mn. These mixtures were then compressed through the cold pressing method at a pressure of 250 MPa. Subsequent reduction and sintering processes were carried out in a tube furnace at temperatures of 1150 and 1400 °C, respectively. Microstructural characterization was conducted using both optical and electron microscopy. The results showed that the change in chemical composition is not significantly effective on the sintering density of the samples and also the highest sintering density, reaching 90.11%, was achieved with the 88W-10Ni-2Mn sample. Furthermore, the results demonstrated that carburization of W-Ni-Mn WHAs during the sintering process led to an increase in the micro-hardness of the samples. The highest hardness, measuring 381 Hv, was observed in the 90W-6Ni-4Mn alloy, where carburization occurred. XRD results revealed that an increase in the nickel-to-manganese ratio led to a reduction in the peaks of manganese carbide and tungsten carbide. Consequently, this decrease in carbide peaks resulted in a reduction in hardness, reaching 352 Hv in the case of the 88W-10Ni-2Mn sample. Additionally, the alloys 90W-6Ni-4Mn and 88W-10Ni-2Mn both exhibited the lowest continuity, a value of 0.5. Fracture surface SEM images illustrated that the 90W-6Ni-4Mn alloy, characterized by the lowest nickel-to-manganese ratio (1.5), exhibited the highest trans-granular fracture mode involving cleavage and matrix tearing, which is considered desirable. Furthermore, an increase in the matrix phase content resulted in a shift of the preferred crack path, originating from the matrix phase.
